Pyramis Essential White Vent Hood with a width of 60cm and a maximum extraction rate of 352 m³/h. It features 2 motors, 3 speeds, aluminum filters, and the option to install a carbon filter.
Specifications are collected from official manufacturer websites. Please verify the specifications before proceeding with your final purchase. If you notice any problem you can
report it here.
Luckily, it took the double socket from the old extractor fan, so I installed 2 bulbs. I preferred it for the double lighting compared to the 065029601, which is not true. The good thing is that it can reach up to 40W. There is no label with a serial or model number, but a sticker of the plate inside. The ventilation cut design on the front is also not like in the photo. It has simple vertical cuts that ruin its entire appearance compared to what I see here. It only comes with 4 screws for mounting on the cabinet and without plugs and screws for wall mounting. While the old one fit perfectly on the bottom of the cabinet with the screws, the Pyramis one leaves at least a 2-inch gap. Maybe because of its design. I tried cutting the air vent a bit without success, and in the end, it went into the wall with plugs and screws. I will keep the product
Attention to the order as the extractor comes in a box without bubbles or any foam. Company's excuse: that's how they send them from the factory... It arrived the first time with a hole in it and damage to the filter due to poor handling. In the next two days, today, it came fine with a small leak in the filter which I fixed. Edit... I also installed a large AC fan at the outlet of the pipe outside the house but there is a small difference. Not only does it not suck well, but it seems to block the steam because even at full power, instead of sucking the steam goes up and escapes to the right and left... I wouldn't buy it again...
Give a chance they say to Greek companies.
First and foremost, I bought a new extractor hood as I changed the entire kitchen, resulting in the melamine swelling after a year.
Of course, it doesn't suck anything for 2 motors, only a little on 3.
The lighting is terrible as well as the design.
The worst part is that just months after 2 years when the warranty expired, one of the 2 motors broke.
Not recommended.
My choice and persistence for a Greek Pyramis extractor hood was a complete failure.... it doesn't extract steam at all.... it has two motors, I thought it would do the job.... oh, a thousand times Chinese.... shame on you (to the manufacturing company)!!!
With a pot, it sucks up half the steam. It makes quite a noise. If you have the means to get something better, do it. This one struggles to suck up two cigarettes at the same time. It was bought as a temporary solution until the previous one is repaired
But features in pyramis, but in the paper that accompanied him in terms of 300m3/h.
A mediocre extractor fan. Unfortunately, in this style there is nothing good. Only if the cabinet above the extractor fan is abolished and we go at least to a sliding type, we may find something that pulls 600m3/h. All these here are mediocre.
One of the worst...... it doesn't pull, in the first month the button that turns on the light broke and when the bulb burns out you can't put your hand to change it. They told me to remove the plastic cover underneath, I tried very carefully and it ended up breaking.
It simply sucks. It has a small nozzle. The tilt it has at the bottom shows that it has been installed crookedly (all my guests ask who installed it crookedly!). The laughable thing is the nonexistent build quality. All the plastics are poorly placed. Its back, on which it leans against the wall, is not reinforced with metal, resulting in the whole hood wobbling up and down. I had to screw it onto the chimney to support it better. The lamp (Turkish-made) was not properly screwed from the beginning and it burned out on the third day. To change the bulb, you can't fit your hand. I called an electrician who took it down and also changed the wires and socket, which were dangerous. The metal filters do not securely lock (I'm waiting for them to fall into the food). I bought it for 70 euros, but I don't know how much it will cost me in money and time...
For the money, it is very good, it has good performance and is a bit noisy as I expected since it is an extractor. I would characterize it as value for money